Controlling air pollution  

courtesy:Green force engineers Pvt. ltd. 


 Introduction

 

Clean air, an essential component of a healthful environment, is a mixture of many different gases. Two gases predominate: nitrogen, which makes up 78 percent of the volume of clean dry air, and oxygen, which makes up 21 percent. Argon, an inert element, accounts for almost 1 percent of clean dry air, and the remainder includes very small or trace concentrations of carbon dioxide, methane, hydrogen, helium, ozone, and other gases. In the Earth's atmosphere, water vapour is also a significant component but the most variable one, ranging from 0.01 to 4 percent by volume; its concentration in air varies daily and seasonally, as well as geographically.

Air is considered to be polluted when it contains certain substances in concentrations high enough and for durations long enough to cause harm or undesirable effects. These include adverse effects on human health, property, and atmospheric visibility. The atmosphere is susceptible to pollution from natural sources as well as from human activities. Some natural phenomena, such as volcanic eruptions and forest fires, may have not only local and regional effects but also long-lasting global ones. Nevertheless, only pollution caused by human activities, such as industry and transportation, is subject to mitigation and control.

 

Most air contaminants originate from combustion processes. In the Middle Ages the burning of coal for fuel caused recurrent air-pollution problems in London and in other large European cities. Beginning in the 19th century, in the wake of the Industrial Revolution, increasing use of fossil fuels intensified the severity and frequency of air-pollution episodes. The advent of mobile sources of air pollution--i.e., gasoline-powered highway vehicles--had a tremendous impact on air quality problems in cities. It was not until the middle of the 20th century, however, that meaningful and lasting attempts were made to regulate or limit emissions of air pollutants from stationary and mobile sources and to control air quality on both regional and local scales.

The focus of air-pollution regulation in industrialized countries was initially on protecting ambient or outdoor air quality. This involved the control of a small number of specific criteria pollutants known to contribute to urban smog and chronic public health problems. Toward the end of the 20th century, the hazardous effects of trace amounts of many other air pollutants were recognized, and emission regulations were implemented. Long-term and far-reaching effects of certain substances on atmospheric chemistry and climate were also observed at that time, and cooperative international efforts were begun to mitigate their global effects.
 Techniques for controlling air pollution

 

Control of particulates

Airborne particles can be removed from a polluted airstream by a variety of physical processes. Common types of equipment for collecting fine particulates include cyclones, scrubbers, electrostatic precipitators, and baghouse filters. Once collected, particulates adhere to each other, forming agglomerates that can readily be removed from the equipment and disposed of, usually in a landfill.

Because each air-pollution control project is unique, it is usually not possible to decide in advance what the best type of particle collection device (or combination of devices) will be; control systems must be designed on a case-by-case basis. Important particulate characteristics that influence the selection of collection devices include corrosivity, reactivity, shape, density, and especially size and size distribution (the range of different particle sizes in the airstream). Other design factors include airstream characteristics (e.g., pressure, temperature, and viscosity), flow rate, removal efficiency requirements, and allowable resistance to airflow. In general, cyclone collectors are often used to control industrial dust emissions and as precleaners for other kinds of collection devices. Wet scrubbers are usually applied in the control of flammable or explosive dusts or mists from such sources as industrial and chemical processing facilities and hazardous-waste incinerators; they can handle hot airstreams and sticky particles. Electrostatic

 

Types of Air Pollution Control Devices

  1. Electrostatic Precipitator
  2. Wet Scrubber
  3. Cyclone
  4. Baghouse

 

 Electrostatic Precipitator

 
Electrostatic precipitation is a commonly used method for removing fine particulates from airstreams. In an electrostatic precipitator, particles suspended in the airstream are given an electric charge as they enter the unit and are then removed by the influence of an electric field. The precipitation unit comprises baffles for distributing airflow, discharge and collection electrodes, a dust clean-out system, and collection hoppers. A high DC voltage (as much as 100,000 volts) is applied to the discharge electrodes to charge the particles, which then are attracted to oppositely charged collection electrodes, on which they become trapped.

Particles that stick to the collection plates are removed periodically when the plates are shaken, or "rapped." Rapping is a mechanical technique for separating the trapped particles from the plates, which typically become covered with a 6-mm (0.2-inch) layer of dust. Rappers are either of the impulse (single-blow) or vibrating type. The dislodged particles are collected in a hopper at the bottom of the unit and removed for disposal. An electrostatic precipitator can remove particulates as small as 1 m (0.00004 inch) with an efficiency exceeding 99 percent. The effectiveness of electrostatic precipitators in removing fly ash from the combustion gases of fossil-fuel furnaces accounts for their high frequency of use at power stations.In a typical unit the collection electrodes comprise a group of large rectangular metal plates suspended vertically and parallel to each other inside a boxlike structure. There are often hundreds of plates having a combined surface area of tens of thousands of square metres. Rows of discharge electrode wires hang between the collection plates. The wires are given a negative electric charge, whereas the plates are grounded and thus become positively charged.
 
 Wet Scrubber

 

 

 

 

Devices called wet scrubbers trap suspended particles by direct contact with a spray of water or other liquid. In effect, a scrubber washes the particulates out of the dirty airstream as they collide with and are entrained by the countless tiny droplets in the spray.

Several configurations of wet scrubbers are in use. In a spray-tower scrubber, an upward-flowing airstream is washed by water sprayed downward from a series of nozzles. The water is recirculated after it is sufficiently cleaned to prevent clogging of the nozzles. Spray-tower scrubbers can remove 90 percent of particulates larger than about 8 m (0.0003 inch).

In orifice scrubbers and wet-impingement scrubbers, the air and droplet mixture collides with a solid surface. Collision with a surface atomizes the droplets, reducing droplet size and thereby increasing total surface contact area. These devices have the advantage of lower water-recirculation rates, and they offer removal efficiencies of about 90 percent for particles larger than 2 m (0.00008 inch).

Venturi scrubbers are the most efficient of the wet collectors, achieving efficiencies of more than 98 percent for particles larger than 0.5 m (0.00002 inch) in diameter. Scrubber efficiency depends on the relative velocity between the droplets and the particulates. Venturi scrubbers achieve high relative velocities by injecting water into the throat of a venturi channel--a constriction in the flow path--through which particulate-laden air is passing at high speed.

 
 Cyclone

 

A cyclone removes particulates by causing the dirty airstream to flow in a spiral path inside a cylindrical chamber. Dirty air enters the chamber from a tangential direction at the outer wall of the device, forming a vortex as it swirls within the chamber. The larger particulates, because of their greater inertia, move outward and are forced against the chamber wall. Slowed by friction with the wall surface, they then slide down the wall into a conical dust hopper at the bottom of the cyclone. The cleaned air swirls upward in a narrower spiral through an inner cylinder and emerges from an outlet at the top. Accumulated particulate dust is periodically removed from the hopper for disposal.

Cyclones are best at removing relatively coarse particulates. They can routinely achieve efficiencies of 90 percent for particles larger than about 20 m (0.0008 inch). By themselves, however, cyclones are not sufficient to meet stringent air quality standards. They are typically used as precleaners and are followed by more efficient air-cleaning equipment such as electrostatic precipitators and baghouses.

 

 

 
 Bag House

 

One of the most efficient devices for removing suspended particulates is an assembly of fabric filter bags, commonly called a baghouse. A typical baghouse comprises an array of long, narrow bags--each about 25 cm (10 inches) in diameter--that are suspended upside down in a large enclosure. Dust-laden air is blown upward through the bottom of the enclosure by fans. Particulates are trapped inside the filter bags, while the clean air passes through the fabric and exits at the top of the baghouse.

Bag house Arrangement

A fabric-filter dust collector can remove very nearly 100 percent of particles as small as 1 m (0.00004 inch) and a significant fraction of particles as small as 0.01 m (0.0000004 inch). Fabric filters, however, offer relatively high resistance to airflow, and they are expensive to operate and maintain. Additionally, to prolong the useful life of the filter fabric, the air to be cleaned must be cooled (usually below 300 °C [570 °F]) before it is passed through the unit; cooling coils needed for this purpose add to the expense. (Certain filter fabrics--e.g., those made of ceramic or mineral materials--can operate at higher temperatures.)

Several compartments of filter bags are often used at a single baghouse installation. This arrangement allows individual compartments to be cleaned while others remain in service. The bags are cleaned by mechanical shakers or by reversing the flow of air, and the loosened particulates are collected and removed for disposal.